Water is collected from a channel and transported to next treatment. Along this path, all the particles of type that have a grainy sedimentation rate greater than the rate of climb of current are held in tub. In practice, the sedimentation depends on surface of tub and not by its volume (survival water purification systems). In fact the same flow rate of upward flow (Qa), the greater the surface (S) of tub, the lower the speed of upward flow (Va = Qa / S), the greater the proportion of particles sedimenting.
These sources of supply, due to specific characteristics of waters and / or the degree of pollution, must be subjected to cycles of treatments of filtration necessary to modify the characteristics and improve its quality. Often, this happens even for the deep waters with a high content of organic substances and a high microbial contamination, especially if they are present faecal bacteria (eg. Coliforms).
Filtration is a treatment used to remove suspended solids from the waters not sediment. Treatment consists in passing the raw waters through a filter medium (bed / filter layer or filter cloth). In case of filter layer, the filter material can be made from quartz sand, anthracite or activated charcoal. During filtration the filtered solids gradually begin to clog the filtering layer resulting in an increase of load losses, which is increased to overcome the supply pressure. Exceeded the maximum value of said pressure must be made to interruption of flow and to cleaning of filter medium.
The filtering layer resting on a draining bottom, which has the function of: surface filters: filtration takes place through filter cloths which prevent the passage from the materials above the size of blind holes (not es.tessuto tissue; in this case the particles are retained on the surface of filter media forming a layer of material that retains the subsequent particles.
ants: the most used today are the polyelectrolytes. The agitation speed should be neither too low to prevent sedimentation of flakes, or too high to avoid breakage of flake. The slow agitation is achieved by use of mechanical mixers (dynamic system) or by placing a series of baffles in tank (static system).
Filter volume: the filtration takes place by means of a three-dimensional porous matrix said filter bed consisting of discrete materials of small dimensions (eg. Sand); in this case the particles are retained within filter medium. The effectiveness of a filter material depends on certain properties of particles such as size, shape and surface chemistry. The filters lenses are the first filtration system used in filtration, but they are currently little used. The slow filtration can be used in case of turbidity 10 ppm.
The filters are formed from cylindrical vessels made of reinforced concrete on the bottom of which special shelves, provided with an adequate number of holes, support the filtering mass. The filter bed consists of fine sand / fine or other material minute. The filter bed is supported by an underlying layer of material, also the filter, formed by a layer of coarse gravel and the overlying layers of gravel gradually finer (mattress draining).
These flocculants, added in small doses, immediately after the coagulant, improve the efficiency of process affecting mainly. The adjuvants used are polyelectrolytes, organic macromolecules obtained through polymerization processes, waters-soluble or dispersible well, characterized by the presence of charged groups or at least polar throughout the chain.
These sources of supply, due to specific characteristics of waters and / or the degree of pollution, must be subjected to cycles of treatments of filtration necessary to modify the characteristics and improve its quality. Often, this happens even for the deep waters with a high content of organic substances and a high microbial contamination, especially if they are present faecal bacteria (eg. Coliforms).
Filtration is a treatment used to remove suspended solids from the waters not sediment. Treatment consists in passing the raw waters through a filter medium (bed / filter layer or filter cloth). In case of filter layer, the filter material can be made from quartz sand, anthracite or activated charcoal. During filtration the filtered solids gradually begin to clog the filtering layer resulting in an increase of load losses, which is increased to overcome the supply pressure. Exceeded the maximum value of said pressure must be made to interruption of flow and to cleaning of filter medium.
The filtering layer resting on a draining bottom, which has the function of: surface filters: filtration takes place through filter cloths which prevent the passage from the materials above the size of blind holes (not es.tessuto tissue; in this case the particles are retained on the surface of filter media forming a layer of material that retains the subsequent particles.
ants: the most used today are the polyelectrolytes. The agitation speed should be neither too low to prevent sedimentation of flakes, or too high to avoid breakage of flake. The slow agitation is achieved by use of mechanical mixers (dynamic system) or by placing a series of baffles in tank (static system).
Filter volume: the filtration takes place by means of a three-dimensional porous matrix said filter bed consisting of discrete materials of small dimensions (eg. Sand); in this case the particles are retained within filter medium. The effectiveness of a filter material depends on certain properties of particles such as size, shape and surface chemistry. The filters lenses are the first filtration system used in filtration, but they are currently little used. The slow filtration can be used in case of turbidity 10 ppm.
The filters are formed from cylindrical vessels made of reinforced concrete on the bottom of which special shelves, provided with an adequate number of holes, support the filtering mass. The filter bed consists of fine sand / fine or other material minute. The filter bed is supported by an underlying layer of material, also the filter, formed by a layer of coarse gravel and the overlying layers of gravel gradually finer (mattress draining).
These flocculants, added in small doses, immediately after the coagulant, improve the efficiency of process affecting mainly. The adjuvants used are polyelectrolytes, organic macromolecules obtained through polymerization processes, waters-soluble or dispersible well, characterized by the presence of charged groups or at least polar throughout the chain.
About the Author:
You can visit defpg.com for more helpful information about Guide To Survival Water Purification Systems.
Comments :
0 comments to “Abcs Of Survival Water Purification Systems”
Post a Comment